| Interface |
QTY |
QTY |
| MIPI-DSI |
1 |
One 4-lane MIPI display serial interface, each lane supports up to 1.5 Gbps
Up to 1920 x 1080@60fps
|
Pin multiplexing interface, choose one |
| Parallel RGB |
1 |
One parallel display interface, up to WXGA (1280x800@60fps) |
| MIPI-CSI |
2 |
two 4-lane MIPI camera serial interfaces, 4lane up to 4000Mbps |
Pin multiplexing interface, choose one |
| DVP |
2 |
Support ITU-R BT.656 (support Interlace, YcbCr422 8-bit/10-bit)
Support HD, 30 fps (YCbCr422 Interleave), 60 fps (YCbCr422 Y/CbCr separate data, binary data)
Maximum input pixel clock: 74.25MHz
Input data format: YcbCr422 8-bit / 10-bit; Binary data 16-bit.
|
| USB HOST |
1 |
USB 2.0 (up to 480 Mbps) |
| USB OTG |
1 |
USB 2.0 (up to 480 Mbps) |
| QSPI |
1 |
maximum clock frequency: 50 MHz (Quad-SPI DDR), 66 MHz (Quad-SPI SDR), 100 MHz (Octal-SPI, HyperFlash) |
| SD |
1 |
1-bit / 4-bit SD bus, support default, high speed, UHS-I/SDR50, SDR104 transmission mode |
| Audio |
≤4 |
Support I2S, mono, tdM mode |
| Ethernet |
≤2 |
1000/100/10 Mbps
IEEE802.3 PHY RGMII and IEEE802.3 PHY MII
|
| CAN FD |
≤2 |
CAN-FD ISO 11898-1 (CD2014), up to 4Mbps |
| I2C |
≤3 |
Support master mode and slave mode, support multi-master operation, support timeout detection
Support 7bit and 10bit slave address format
|
| UART |
≤5 |
Supports separate 16-byte FIFO registers for transmit and receive
Support full duplex mode
Supports modem control functions (channels 0, 1 and 2 in asynchronous mode)
|
| UART |
≤2 |
without FIFO
without FIFO
Support modem control function
Selectable Clock Synchronous Mode, Asynchronous Mode or Smart Card Mode
Encode and decode IrDA communication waveforms according to IrDA 1.0 (on channel 0)
|
| SPI |
≤3 |
Supports master mode and slave mode
Programmable bit length, clock polarity, clock phase selectable
up to 50 Mbps
|
| MTU3 |
≤9 |
Multi-function Timer Pulse Unit 3
Supports Toggle, PWM, Complementary PWM and Reset Synchronous PWM modes
Support dead time compensation counter function
Digital filter function supporting input capture and external count clock pins
|
| GPT |
≤8 |
General PWM Timer
Support counting up or down (sawtooth wave), counting up or down (triangle wave)
Independently selectable for each channel, 2 input/output pins per channel
|
| WDT |
3 |
Watchdog Timer
WDT CH0: WDT to check the operation of Cortex-A55-CPU Core0
WDT CH1: WDT to check the operation of Cortex-A55-CPU Core1
WDT CH2: WDT to check the operation of Cortex-M33 CPU
|
| ADC |
8 |
Resolution: 12-bit
Input voltage: 0V~1.8V
Conversion Time: 1us
Operation Mode: Single Scan/Continuous Scan
A/D conversion start condition:
· Software trigger
· Asynchronous trigger (support external trigger)
· Synchronous triggering (MTU and PWM timers)
|
| JTAG |
1 |
debug |
